Identify Your Bucket Tooth

Unsure what bucket teeth you've got on your digger? Use this handy guide to find out.

There are several ways to determine your bucket tooth fitment style and size. At The Wearparts Depot we only stock bucket teeth for 3-ton diggers and larger. Before we start, there is one obvious place to look for a part number.

The part number of a bucket tooth is typically cast into the interior wall or rear edge of the tooth pocket. If you can't locate it or make it out, then follow our guide below.

 

1. Side pin or top pin

SIDE PIN

There are many side pin bucket tooth fitment styles. By far the most popular is the Cat J-Series. We also stock Komatsu bucket teeth.

Here's how to tell which is which.

 

CAT J-SERIES

Cat J-Series pins run horizontally through the tooth and adapter.

J-series has a pin and separate retainer. The pins have a recessed groove at one end to seat the retainer that is inserted into the adapter.

 

J-Series adapters have a recessed area on one side of the nose that retainer is inserted into.

View our Cat J-Series bucket tooth selection here

 

KOMATSU

Komatsu bucket teeth have an integrated centre-ring pin and retainer that looks like this.

Komatsu adapters can be distinguished from Cat J-Series because they have no recessed area for a retainer on the nose.

View our Komatsu bucket tooth selection here

TOP PIN

ESCO CONICAL 

ESCO Conical bucket teeth have a vertical pin system. The hole is on the top and is rectangular shape with a square top and rounded bottom.

 

The pins and rubber retainers look like this:

 

The top end of the tooth tends to have a rounded shape that fits into a concave counterspace on the adapter.

View our ESCO Conical bucket tooth selection here.

 

2. Machine size

Once you have identified the fitment style the next step is to confirm the fitment size. The quickest way to narrow down where to look is to use the machine size. The correct size adapters should be fitted to a bucket that is designed for a specific machine size. Correct advice isn't always followed but it is a good start to help identify your fitment size.

Here is a handy chart that matches the correct machine tonnage with fitment sizes:

Tonnage 4-6 7-8 7-10 10-15 15-20 20-25 25-30 35-40 45-50 50-60
Cat
J-Series
J200 J225 J225 J250 J300 J350 J400 J460 J550 J600
ESCO Conical 18 22 25 30 35 40 45 50
Komatsu 200 (205) 200 (205) 200 (205) 300 (207) 400 (208) 600 (109) 600 (109)

 

3. Pin and retainer size

Measuring your pins and retainers is the most accurate way to determine your fitment size because they are manufactured to more exacting measurements than cast teeth.

Now that you know what fitment size matches your machine tonnage you can view the product listings for the pin and retainer in that size. For example simply search "J250 pin" in the search box at the top of the website.

Each product listing has a table of measurements that reference a diagram in the product image gallery.

Check that the measurements of your pin/retainer closely match those listed to confirm your fitment size. If the measurements differ then check the measurements of pin/retainers for the fitment sizes above and below this to see if you find a better match.

 

4. Tooth pocket size

If you're still unsure, or you want to double-check your result, you can measure the interior pocket opening of your worn/other teeth. The pocket is the area that the adapter nose fits into. The interior pocket is subject to minimal wear during the life of a bucket tooth. This makes it a good location to compare measurements.

Measure the height and width of the top/rear opening of the pocket and compare with the table of measurements on a product listing on the website. If you find a close match then you're looking at the right product. 

 

5. Success!

If you feel confident that you've identified your tooth then you can add the products to your cart and place your order. 

If you're still unsure then we would recommend purchasing your bucket teeth from a supplier with a sales team that can perform a site visit to measure up and help you order the correct teeth. We recommend Real Steel for this service.

DISCLAIMER

The Wearparts Depot is not responsible for customers who use this guide and order the wrong teeth. We offer a 90-day returns policy if you make an incorrect purchase.

Continue shopping
Your Order

You have no items in your cart